SBA Service-Disabled Veteran-Owned Certified

Water Softener Repair & Service

Water Pros repairs and services water softeners of any age and any installer, with a flat-rate call and a free return visit if the problem is not fixed. Start with a free local basic test for hardness, iron and pH so we know what your softener is working against.

A softener does its job quietly until it stops. One day the shower glass spots again, the salt level has not moved in weeks, or the tank is hissing, and you are not sure whether to repair the unit or replace it. This page walks through what we look for and why.

Signs Your Softener Needs Service

The most common complaint is simple: the water is hard again. Soap does not lather, white spots return on glassware and fixtures, and skin and laundry feel the way they did before the softener went in. The USGS rates water as soft up to 60 mg/L of hardness, moderately hard at 61 to 120, hard at 121 to 180 and very hard above 180. One grain per gallon equals 17.1 mg/L, which is how most softener settings are expressed.

Other signs point to specific parts of the system:

  • No soft water at all, or soft water that comes and goes
  • A hissing sound from the valve or tank
  • Salt that is not going down, or salt that disappears faster than usual
  • A hard crust or a hollow space in the brine tank
  • A salty taste, or a control head showing odd cycles
Two treatment tanks and a brine tank with bags of softener salt

What a Service Visit Checks

Our maintenance checklist for a softener is the same whether we installed it or not. We open the control valves and clean the internal components, verify brine draw and refill, confirm media movement, regeneration cycles and settings, and sanitize the media and the salt tank on each visit.

Most repairs are found in that list: a brine line that cannot draw, a valve with a worn internal part, or settings that no longer match the household's water use. Because our technicians carry common parts, many of these are finished on the first visit. If the issue is not resolved, we will return at no additional charge. The wider picture of what we do is on our service and repair page.

Water softener and brine tank beside an electrical panel

Salt Bridges and Salt Use

A salt bridge is a hard crust that forms across the salt in the brine tank, leaving an empty space underneath. The softener looks like it has salt, but no brine is being made, so the resin stops being recharged and hard water comes through. Humidity or a mix of salt types are common reasons the crust forms. We break it up, clean the tank and check why it formed.

Using too much salt is the opposite problem and often has a settings answer: a regeneration schedule that runs more often than the household needs, or a salt dose set higher than the hardness calls for. Our guides explain both: why a softener uses too much salt and how often to add salt.

Repair or Replace: Test the Water First

Before anyone talks about a new unit, we test. Free local basic testing includes hardness, iron and pH, and you don't have to be an existing customer. If the hardness reading is high and the softener is old, the numbers help decide whether a repair is worth making or whether a new water softener is the better path.

Iron deserves a mention. A softener can remove up to 4 ppm of iron, but the resin then needs cleaning about monthly. When iron is higher than that, an iron filter ahead of the softener usually protects the resin. We inspect softeners once a year as part of a maintenance plan, which catches small issues before they become no-soft-water calls.

Water Softener Repair & Service: Questions

Can you repair a softener you did not install?

Yes. We service most water treatment equipment even if it was not installed by us, and you don't have to be an existing customer. We may ask for system details or photos first.

How often should a softener be inspected?

Once a year. A yearly visit covers the valves, brine draw, regeneration settings and sanitizing, and it is the easiest way to keep soft water consistent.

What is a salt bridge?

It is a hard crust that forms over the salt in the brine tank, leaving a hollow underneath so no brine is made. We break it up, clean the tank and look for what caused it.

My softener runs but the water is still hard. Why?

Common causes are a salt bridge, a brine line that is not drawing, spent or fouled resin, or settings that no longer match the water. A hardness test and a look at the valve usually pinpoint it.

How is a service call billed?

Service calls are a flat-rate service call fee with no hourly labor charges and no fuel surcharges. If your issue is not resolved during the initial visit, we will return at no additional charge.

Does iron affect my softener?

It can. A softener can remove up to 4 ppm of iron, but the resin then needs cleaning about monthly. Higher iron is better handled by a dedicated iron filter.

More questions and answers

Sources (4)

What customers say about our water softener work

4.9 on Google from 55 reviews

Kelsey Songey

Posted on Google

Great price very friendly and we love our water softener and reverse osmosis setup! Would highly recommend. Worked fast and with care too.

Response from the owner

Thank you so much for the review! We’re thrilled to hear that you’re loving your new water softener and reverse osmosis system. We truly appreciate your kind words about our service and are so glad we could make the process quick, easy, and stress-free for you. Thank you for choosing Water Pros and for recommending us—it means a lot to our entire team!

Rosemary Eddy

Posted on Google

Competent, reliable, honest, cheerful: we are delighted with out water softener and the excellent service we received.

Response from the owner

Thank you so much for the kind review. We’re so glad you’re happy with your water softener and the service you received. We truly appreciate your support and trust in us!

J and R Miller

Posted on Google

We have been using Gardner’s Water Service for 4+ years- ever since we built our house which uses well water. I am very picky about the taste (and smell) of my water and Gardner’s made it all Great! They will call to remind me it’s time to make a maintenance appointment. They have always been on time for the appts. And Bill always explains what (and why) he’s done to our system for maintenance.

I definitely recommend Gardner’s to make a new water conditioning system or for up-grading or maintenance of one.

Response from the owner

Thank you so much J & R. We greatly appreciate your feedback! Thank you for your continued support!

Offering you the quality Water Treatment Services you deserve!

Free local basic testing to include hardness, iron & pH. Service on most water treatment systems, even ones we did not install.

or call 775-674-2871

★★★★★ 4.9 on Google from 55 reviews

Monday - Friday - 8am to 4:30pm

Get in Touch