SBA Service-Disabled Veteran-Owned Certified

Does Reverse Osmosis Remove Arsenic?

Reverse osmosis & drinking water · 8 min read · Updated November 2026

Reverse osmosis removes most arsenic: in a U.S. Geological Survey study of 59 Lahontan Valley homes, the household systems averaged 80.2 percent removal. Because 18 of those 59 homes still had treated water above the 10 parts per billion federal limit, the way to be sure is to test the treated water.

Key points

  • USGS studied household RO systems in 59 Lahontan Valley homes and found an average arsenic removal of 80.2 percent.
  • In 18 of the 59 homes the treated water was still over the EPA limit of 10 ppb.
  • The form of arsenic and the starting level both matter.
  • A lab test of the treated water, not taste or a TDS meter alone, confirms the result.
Reverse osmosis filters and white storage tank installed under a kitchen sink

What did the USGS study find?

The U.S. Geological Survey studied how well household reverse osmosis systems work in the Lahontan Valley of Nevada, an area where groundwater arsenic is common. It tested 59 homes with RO systems. Average arsenic removal was 80.2 percent, which is a strong result, and it is the reason RO is a common answer for drinking water on arsenic wells.

The same study found that 18 of the 59 homes still had arsenic above 10 ppb in the treated water. The federal drinking water limit, set by the EPA, is 10 ppb. The study's authors pointed to two main reasons, covered below, and they recommended directly testing treated water.

Why can treated water still be over the limit?

Two things stood out in the study. First, some wells had arsenic so high to begin with that even more than 95 percent removal left a result above 10 ppb. A percent is only half the story: a system that removes 95 percent from water carrying 400 ppb still delivers 20 ppb.

Second, arsenic comes in two common forms, arsenate (As V) and arsenite (As III). RO rejects the As V form well and the As III form less well. The USGS reported that trivalent arsenic was the dominant form in about 15 percent of the wells. The Nevada Division of Environmental Protection's guidance on matching problems to treatment also notes that arsenic treatment generally involves oxidizing before treatment, so the form of the arsenic matters when choosing equipment.

The study also found three homes where treatment barely changed the water's conductivity, which suggested those systems were not working as intended, and that conductivity drops did not always match arsenic drops. In short: a system can look fine and taste fine and still need a test.

How do I know what arsenic is in my water?

Arsenic has no taste, color or smell, so only a certified lab test can tell you. The EPA's limit for arsenic is 10 parts per billion (0.010 mg/L). A broader picture of why it matters here comes from a 2022 study of 174 Nevada domestic wells led by the Desert Research Institute, which found 22 percent above the arsenic limit. Our guide on arsenic in Nevada well water covers the regional data.

For a private well, order a lab analysis through a Nevada-certified lab; see how to test well water in Nevada. City water customers can read their utility's annual water quality report, which gives arsenic as a running average.

What does a good arsenic plan look like?

Treat what the test finds, and then test again. For drinking and cooking water at one tap, an RO system is a sound point-of-use choice. For arsenic in the whole house supply, or for arsenic that is high or in the As III form, whole-house arsenic media may be the better fit, and our arsenic filtration page describes that approach.

What does a good arsenic plan look like?
SituationTypical approachThen
Moderate arsenic, drinking water onlyReverse osmosis at the kitchen sinkLab test the treated water
High starting arsenicWhole-house arsenic treatment, with RO as a final polish if wantedLab test before and after
Arsenic mostly in As III formOxidize first, then treatLab test the result
UnknownLab test the raw water firstChoose equipment from the result

Our point-of-use versus whole-house guide explains when each fits.

What does Water Pros do about arsenic and RO?

We begin with a test. Free local basic testing covers hardness, iron and pH, and lab testing, which is typically required for well water, covers arsenic. You do not have to be an existing customer. Then we install reverse osmosis or arsenic treatment where the numbers call for it.

Keeping an RO system healthy keeps its performance steady. Our reverse osmosis service replaces the pre- and post-filters, sanitizes the housing and faucet, tests TDS to verify membrane performance and checks pressure. We recommend retesting treated water after installation and after the membrane is replaced. Call 775-674-2871 or send a message through the form below.

Sources (6)

Related questions

What percent of arsenic does reverse osmosis remove?

In the USGS study of 59 Lahontan Valley homes the average was 80.2 percent. Results vary with the starting arsenic level and its chemical form.

What is the arsenic limit in drinking water?

The EPA's maximum contaminant level for arsenic is 10 parts per billion, in effect since January 23, 2006.

Is a TDS meter enough to check my RO for arsenic?

A TDS reading shows how well dissolved solids are rejected, which is useful. The USGS found that conductivity drops did not always match arsenic drops, so a lab test of the treated water is how to be sure.

How often should I test treated water?

Test after installation and after major service such as a membrane change, then follow the schedule you set for your well. We recommend a full analysis every 3 to 5 years.

More questions and answers

Offering you the quality Water Treatment Services you deserve!

Free local basic testing to include hardness, iron & pH. Service on most water treatment systems, even ones we did not install.

or call 775-674-2871

★★★★★ 4.9 on Google from 55 reviews

Monday - Friday - 8am to 4:30pm

Get in Touch